Overview: A 30kW Board for the Megawatt Rack

On November 17, 2026, xPower (讯湃科技) held an 800V power product launch and AI DC energy infrastructure forum at its Shanghai R&D center, unveiling what it describes as the industry's first 30kW 800V power distribution board (PDB). Alongside the PDB, the company showed a 12kW high-voltage power module and an LV-IBC low-voltage series, presenting a full board-level power chain aimed at AI data centers (AIDC). The timing is pointed: as rack power climbs toward hundreds of kilowatts and then megawatts, the 54V bus that has anchored data center distribution for decades is reaching physical limits.

From Wafer Fab to Substation: Why 54V Breaks

The article frames the shift bluntly: the first constraint on AI compute is moving from the wafer fab to the substation. The conventional utility-to-board chain — grid, UPS, AC distribution, rack PSU, 54V bus, board-level DC-DC — was designed for loads far below what AI accelerator racks now demand. The arithmetic is unforgiving. A 1MW load carried on a 54V bus draws close to 18,500A and would require more than 200 kilograms of copper, making deployment an engineering ordeal rather than a routine build.

Citing SemiAnalysis research, xPower notes that raising distribution voltage from 54V to 800V cuts current by roughly 15× and reduces conductor resistive losses by about 219×, shrinking copper content, thermal load and conversion losses simultaneously. The same research projects that data center capacity using 800V DC architectures will reach approximately 39GW of new capacity by 2030, with the power rack/sidecar market reaching about $11 billion by 2028.

Technical Details: 180W/in³ in a 330×220×38mm Envelope

The headline PDB performs 800V-to-50V conversion inside a 330×220×38mm enclosure, achieving 180W/in³ power density, 98.4% peak efficiency and 97.9% full-load efficiency. What distinguishes it from a bare converter is the degree of system integration: input fuse protection, hot-swap, EMI filtering, ORing and input discharge are all built onto the board, complemented by over-voltage, over-current, over-temperature, short-circuit and liquid-leak detection, plus telemetry and PMBus communication. High-voltage access, power conversion, runtime protection and status monitoring thus collapse onto a single card, extending the product's value from conversion into system integration and in-service operations.

The Three Architecture Paths

xPower's framing of the transition identifies three competing routes:

  • Legacy 50V DC: grid through transformer and AC-DC PSU to 50V, then board-level conversion. Few conversion stages and a mature ecosystem, but busbars and connectors hit carrying limits as racks approach megawatt class.
  • 800V-to-50V two-stage: a sidecar rectifies 480V AC to 800V DC, then a DC-DC PSU steps down to 50V. The lowest barrier to deployment, at the cost of an extra conversion stage and its losses.
  • Full 800V HVDC: a solid-state transformer (SST) outputs 800V DC directly, and a PDB inside the rack steps down to 48/12/6V before board-level delivery. Fewest stages and highest efficiency ceiling, but demanding on SST, PDB and downstream board-level device maturity.

Companion Products: 12kW Modules and LV-IBC

The 12kW 800V-to-50V module measures 116.8×61×14mm at roughly 2kW/in³, with 98.6% peak efficiency and 98.1% at 10kW output, carrying OVP, OCP, OTP and SCP protection, telemetry and PMBus. The LV-IBC family addresses conversion after the 50/54V bus across quarter-brick, 2317 and 4216 packages, spanning 800W to 3.2kW TDP with peak EDP up to 4.5kW. Notable entries include a quarter-brick at 3.2kW TDP/4.5kW EDP with 97.7% full-load and 98.5% peak efficiency, a 4:1 2317 unit at 2kW TDP/4kW EDP at 96.4%, and a 16:1 4216 device (54V→3.3V) at 800W TDP/2kW EDP and 96% full-load efficiency in a 42×16.5×6mm outline. A VRM tier completes the chain toward sub-volt chip supply.

Manufacturing Footprint and Ecosystem

Chairman and CEO Zha Yingjie, who brings two decades of semiconductor experience, described a China team of nearly 100 people spanning power electronics, structural and thermal design, test and validation, supply chain and customer systems engineering, backed by a self-owned Shanghai production line and partner capacity at home and abroad. COO Lin Dong detailed a fully automated SMT line covering loading, solder spraying, SPI, placement, nitrogen reflow and AOI, plus an arrangement with USI under which the Vietnam Haiphong plant is slated to assemble power modules as the primary overseas manufacturing base. For rack-external power, xPower has formed a strategic partnership with Lingyi iTech on sidecar power, BBU and SST development. The accompanying forum drew experts from eight universities, including Virginia Tech CPES, Tsinghua and Hong Kong University, plus representatives from 12 companies.

Implications and Outlook

The significance is less a single board than a direction of travel. 800V HVDC is not a voltage-level swap but a full-chain rebuild of data center power, from architecture and devices to manufacturing process. With no large-scale commercial 800V DC data center deployments yet delivered, industry projects remain largely technical validation, prototype pilots and ecosystem alignment — precisely the stage at which a 30kW integrated PDB matters as a reference design point. xPower's contribution is a staged answer at the moment 800V moves toward volume commercialization, and one more entry in the wave of 800V DC components from Chinese power suppliers targeting AI infrastructure.