The article describes a modular ISOP architecture using low-voltage GaN devices to convert 800 VDC rack power directly into high-current processor rails. It argues this approach can reduce conversion losses and simplify power delivery for high-density AI servers as racks move toward 800V HVDC.
Overview
AI servers are pushing power architectures in two directions at once: toward higher distribution voltage and toward much higher processor power. An 800 VDC rack bus can reduce distribution losses, but it creates a difficult conversion problem because thousands of watts must be transformed efficiently into low-voltage, very high-current rails close to the load. A technical article by Michael de Rooij of Efficient Power Conversion, co-authored by EPC’s Alejandro Pozo and Ionel “Dan” Jitaru, CEO of Rompower Energy Systems, describes a modular input-series, output-parallel architecture that uses low-voltage GaN devices to address this challenge. The article was published by EEPower as part of an exclusive digital content partnership with Bodo’s Power Systems.
The ISOP Architecture Explained
The input-series, output-parallel architecture is a modular approach based on several identical isolated DC-DC converter modules using an LLC resonant topology. The modules’ outputs are connected in parallel and their inputs in series, allowing the design to scale input voltage and output current simultaneously. In a system with M modules, each module receives only a fraction of the total input voltage, VIN/M, and processes a fraction of the total output power, POUT/M. One important advantage of LLC-based modules in an ISOP string is self-balancing. When the ratio of magnetizing inductance to resonant inductance is properly selected, converter gain is almost constant at resonance, yielding a robust solution insensitive to component tolerances and avoiding complicated control algorithms for voltage and current sharing. The modular architecture also allows LLC modules to be interleaved in phase, significantly reducing output current ripple. For example, a 6 kW, 800 V to 12 V single LLC module has about 754 A peak-to-peak ripple, whereas a four-module interleaved ISOP reduces it to 37 A, lowering output bus capacitance requirements.
Splitting the 800 V Problem into Manageable Blocks
The central idea is straightforward: instead of asking one converter to withstand the full 800 V bus, the architecture shares the input voltage across multiple converter cells. In the designs discussed, eight LLC modules are connected in series on the input and in parallel on the output. Each module therefore sees about 100 V while output currents add together. This changes the semiconductor design space. Lower-voltage GaN transistors can efficiently switch at around 1 MHz, reducing switching and conduction losses compared with higher-voltage devices operating at lower frequencies. The eight phases also distribute power dissipation, simplify thermal management, and reduce output capacitance through interleaving. Transformer construction benefits because each stage handles only a fraction of the total voltage. The modular structure can also be adapted to lower-voltage input configurations by changing the number of modules and their operating voltage.
First Implementation: 800 V to 50 V
The first demonstration targets 800 V-to-50 V conversion at 11 kW. Each LLC processes 100 V and 1.375 kW. The primary half-bridge and center-tapped secondary use the same 150 V GaN transistor, the EPC2305, rated at 2.2 mΩ typical on-resistance. A 1:1:1 transformer and a resonant operating point near 1 MHz complete each module. Mechanically, two LLC stages are integrated into each PCB and magnetic structure, so four vertical boards accommodate the eight modules, with a horizontal control board underneath. Compared with an earlier 400 V-to-50 V implementation, this approach doubles power density while reducing magnetics volume by approximately half. Measured results show 98.5% peak efficiency and 98% efficiency at full load while processing up to 11 kW.
Direct Conversion to 12.5 V and 6.25 V Rails
The same architectural concept can be pushed further. A second converter moves directly from 800 V to 12.5 V, delivering 6 kW. With an overall 64:1 ratio, each of the eight LLC stages converts 100 V to 12.5 V and delivers as much as 750 W. Parallel connection at the output produces up to 480 A. EPC2305 devices remain on the 150 V primary side, while EPC2366 devices, rated at 40 V with 0.8 mΩ typical on-resistance, are used as synchronous rectifiers. The transformer uses a 4:1:1 turns ratio and is integrated into a 14-layer PCB. The complete converter occupies less than 5000 mm² of PCB area and is only 8 mm thick, with GaN devices mounted on the top side for direct thermal coupling to a heat spreader or water-cooled cold plate. It achieves more than 98% peak efficiency and 97% efficiency at full load while delivering 480 A.
The third design addresses a 6.25 V rail. It again uses eight LLC modules, but the overall ratio is 128:1. Each cell converts 100 V to 6.25 V and can deliver 750 W, or 120 A. In parallel, the converter reaches 960 A at 6 kW. At this voltage, every milliohm matters. The design therefore moves to EPC2376 150 V GaN devices on the primary and EPC2379 devices on the secondary. The EPC2379 has a typical on-resistance of just 0.33 mΩ, and four devices in parallel are needed to handle the extreme output current. The PCB uses a 6+6-layer construction in the original design, with an 8+8-layer configuration planned for the next revision. An 8:1:1 transformer ratio and multilayer PCB structures control leakage inductance within the available mechanical height, eliminating the need for a dedicated external leakage inductor. Eight power cells are distributed around the board perimeter, close to current-extraction points, and edge metallization provides a low-impedance path for the combined output current. The complete assembly is 11 mm thick and occupies about 15,400 mm² of PCB area.
Tradeoffs at Lower Voltages
Across the three implementations, the output voltage falls by a factor of eight, from 50 V to 6.25 V, while output current rises dramatically. That progression highlights a fundamental system-level tradeoff: at lower voltage, the converter is increasingly dominated by conduction losses, current distribution, interconnect resistance, and thermal paths. The designs address these issues through coordinated choices in GaN device selection, transformer turns ratios, PCB layer construction, and physical layout. The ISOP approach also provides flexibility beyond a specific 800 V implementation, making the architecture less dependent on a single rack-voltage standard and offering a development path as data-center power distribution evolves.
Implications for AI Data Centers
For high-density AI servers, the value of this modular GaN route lies in converting 800 VDC rack power directly into high-current processor rails with high efficiency and manageable thermal distribution. By dividing the 800 V input among eight LLC stages and combining their outputs, the architecture enables fast, low-voltage GaN devices while distributing heat and current. The three implementations show peak efficiencies ranging from 98.5% to more than 98%, with full-load efficiencies of 97% to 98% at power levels from 6 kW to 11 kW. As racks move toward 800 VDC, such modular ISOP designs could simplify power delivery and reduce conversion losses close to the load.
Future Outlook
The article presents the modular ISOP architecture as a scalable building block rather than a fixed converter. The same structure can be adapted by changing the number of modules and their operating voltage, which may help developers respond as data-center power distribution standards evolve. Planned work includes an 8+8-layer PCB configuration for the 6.25 V design. Overall, the approach illustrates how low-voltage GaN devices, LLC resonant modules, and careful packaging can be combined to address the demanding conversion path from an 800 VDC rack bus to low-voltage, very high-current processor rails.